Stick curtain wall vs unitized: choosing a system for NYC mid-rise and mixed-use jobs
You have a seven-story mixed-use building on a 25 foot lot. Retail at grade, apartments above, a setback at the sixth floor, and a sidewalk shed that already eats half the curb. The architect drew a glass facade. Now someone has to decide how that glass actually gets onto the building, and the choice usually comes down to a stick curtain wall or a unitized system. That decision affects your crane plan, your schedule, your tolerance budget and how much pain you feel if the slab edges are not where the drawings say they are.
I run a fabrication shop in Brooklyn, and we build stick-built curtain wall and storefront for multi-family, office, mixed-use and private residential work. We do not install. The glazing sub on your job erects the wall. So this is written from the shop side: how each approach is built, what it asks of the site, and where each one makes sense. I will be honest about where unitized wins, because it does win on some buildings.
Two ways to build the same wall
Both approaches end in the same place: an aluminum grid hung off the building structure, carrying glass and spandrel panels, resisting wind and keeping water out. A curtain wall is non-load-bearing. It carries its own weight and the wind loads on it and passes those back to the slabs or frame. The difference is where the assembly happens.
How a stick system is fabricated
With a stick system, the shop cuts, machines and prepares individual components: mullions, transoms, pressure plates, cover caps, gaskets, anchors and connection hardware. Everything is cut to length from the shop drawings, drilled and notched for the connections, finished, labelled and bundled by elevation or floor.
The glass is ordered to the grid and delivered separately, or alongside the framing depending on the job. Nothing is assembled into large panels in the shop. The wall gets built piece by piece on the building.
How a unitized system is fabricated
With unitized curtain wall, the factory builds complete panels. Each unit is typically one floor tall and one module wide. The frame is assembled, the glass and spandrel are installed, gaskets and seals are set, and the finished panel ships as a single piece. Adjacent units interlock at their vertical edges and at the stack joint between floors.
That means a lot more engineering up front. The panel sizes, the interlocks, the anchors and the stack joints all have to be resolved before production starts, and every unit is a fixed size once it leaves the factory.
How each one goes up on site
The erection sequence is where the two approaches really split.
Stick: the glazing crew sets anchors at the slab edges, hangs the vertical mullions, fits the horizontal transoms between them, then sets glass and spandrel into the grid. Pressure plates clamp the glass against the gaskets, and cover caps go on last. Most of this work happens from the outside, so the crew needs exterior access: a swing stage, mast climber, scaffold or a lift, depending on the height and the site.
Unitized: anchors go on the slab edges first, then finished panels are lifted into place and hooked onto the anchors from inside the floor plate, usually with a crane, a monorail or a floor-mounted hoist. Each panel interlocks with its neighbour. Once a floor of panels is set, that floor is closed in.
In plain terms: stick moves small, light pieces and does more labor on the building. Unitized moves big, heavy, finished pieces and does more labor in the factory.
Crane and hoisting limits on tight city sites
On a wide suburban site with laydown room, hoisting is a line item. On a mid-block lot in Manhattan, Brooklyn or Jersey City, it can drive the whole facade decision.
Unitized panels are large and they are heavy. They need to be lifted with control and set in sequence, which usually means a crane or a dedicated hoisting setup, plus somewhere to stage the panels before they go up. In the city that brings permits, street or lane closures, restricted working hours and coordination with neighbors. If the crane is not already on the job for the structure, adding one just for the facade is a real cost. If it is on the job, the facade crew is now competing for crane time with every other trade.
Stick components are a different problem. Mullions are long but light. Transoms, caps and plates are smaller still. They can come up in a material hoist, through the building, or be passed out from the floor plate. Glass is the heavy part of a stick job, and large lites still need proper handling equipment, but you are moving one lite at a time rather than a finished panel with glass already in it.
Questions worth asking early on a tight site:
- Will there be a tower crane on the job when the facade goes in, and how much time can the glazing sub actually get on it?
- Where would unitized panels be staged? Is there a floor that can take them, or a lot nearby?
- What are the working hours and closure rules for the street?
- Is there a material hoist that can take long mullion lengths?
- How will the glass be handled at the larger lite sizes?
If most of those answers are bad, a stick system starts to look a lot better.
Tolerances: what the wall has to absorb
No building is built to the drawing. Slab edges move in and out. Floors are not perfectly level. Columns drift out of plumb. On a renovation or a conversion, the existing structure has had decades to move. The curtain wall has to sit on that structure and still read as a flat, straight plane.
Both systems use adjustable anchors to take up some of that variation. The difference is what happens after the anchors.
In a stick system, the frame itself is built in place. If a slab edge is out, the crew can adjust anchor positions, shim, and set mullions to a true line. Glass and spandrels are typically measured and ordered to the grid, and on a tricky bay the field team has the option to verify before the final infill goes in. There is more room to absorb the building as it actually is.
In a unitized system, the panels are fixed sizes built months earlier. The anchors and the stack joints are designed with a set amount of adjustment. If the structure is outside that range, you are into remedial work at the anchor or, worse, a panel that does not fit. That is why unitized projects lean so hard on surveys of the slab edges before production.
For new construction with a well-controlled concrete or steel frame, either approach can work. For conversions, additions onto existing buildings, and frames that are known to be a little loose, stick is the safer bet. I see the same thing at window scale every day in brownstones: openings that are out of square after a century of settling. We build to the measured opening because that is the only way the finished elevation looks right.
Irregular grids and mixed-use elevations
Unitized panels pay off through repetition. The more identical units, the better the economics, because the engineering, tooling and mockups get spread over a lot of panels. That is why unitized is common on tall towers with a regular module running floor after floor.
Mid-rise and mixed-use buildings in New York rarely look like that. A typical elevation might have:
- A tall retail floor at grade with storefront and entrance doors
- Residential floors above with a different module
- A setback with a terrace and a change in grid
- Corner conditions, returns and a parapet
- Operable vents in some bays and not others
- Spandrel panels where the floor and ceiling zones land
Every change in the grid is a new unit type in a unitized system. Do that enough times and you lose the repetition that made unitized worth it. A stick system handles irregular grids much more comfortably because each mullion and transom is cut to its own position. A bay that is a few inches different from its neighbors is just a different cut length, not a new engineered panel.
This is one of the main reasons we work with stick-built curtain wall on our curtain wall systems. The projects we see in the five boroughs, New Jersey and Connecticut tend to have irregular grids, mixed uses and site constraints, and stick handles that better.
Phased delivery and sequencing
On a mid-rise job the facade rarely goes in all at once. The structure tops out floor by floor, some elevations are blocked by scaffolding or a neighbor, and the GC wants to close in the lower floors so interior trades can start.
Stick suits that kind of schedule well. Components can be fabricated and delivered by floor, by elevation or by release, labelled to match the shop drawings so the crew knows exactly where each piece goes. If the sequence changes, the next release changes with it. Material arrives when the crew is ready for it instead of sitting on a floor taking up space.
Unitized can also be phased, but the production run is usually locked further in advance, and every phase needs staging space and hoisting time. If the schedule slips, finished panels sit somewhere waiting.
One more practical point. When a revision comes in late, which happens on almost every job, a stick system is easier to adjust. A mullion length or a transom position can change before that release is cut. When the shop is local, those changes take days, not a round trip across an ocean. Our shop is about forty minutes from most projects we supply, which matters when a field question needs an answer the same week.
Where unitized earns its place
I build stick systems, but I will not pretend unitized has no case. It makes a lot of sense when:
- The building is tall and the grid repeats for many floors
- Enclosure speed per floor is the top priority and the site can support the hoisting
- Field labor is expensive or hard to find for the height involved
- Working from the outside of the building is difficult or unsafe at that height
- There is time in the schedule for the up-front engineering, mockups and production
On a large high-rise with a regular module and a crane on site for the duration, unitized is often the right choice. The question is whether your building is that building. Most mid-rise and mixed-use projects are not.
When a stick curtain wall like MB-SR50N is the right fit
A stick system is usually the better choice when several of these are true:
- The building is mid-rise, roughly the height where exterior access is practical
- The site is tight, with limited crane time or nowhere to stage large panels
- The elevation has irregular grids, setbacks, corners or a mix of storefront and upper floors
- The structure is existing, converted or known to have loose tolerances
- The facade needs to go in by floor, elevation or release
- The project expects design changes during construction
- The building also needs windows and doors that should match the curtain wall
What MB-SR50N brings
The MB-SR50N curtain wall system is the Aluprof stick system we fabricate for most curtain wall and storefront work. It is a mullion and transom grid with a 50 mm sightline. Mullion depth is chosen based on glass weight, span and wind pressure, so the profile is sized to the actual bay rather than one depth for everything.
From Aluprof's published system data:
- Airtightness AE 1200 and watertightness RE 1200
- Impact resistance I5/E5
- Infill load capacity up to 1,100 kg for applicable configurations
- EPDM glazing gaskets and HPVC thermal barriers
- Variants including MB-SR50N EI (fire-rated), higher-insulation and semi-structural options, and horizontal or vertical line expression
These are system figures from the manufacturer. Real performance on your building depends on size, glazing, configuration and site conditions, which is why we put the glazing build-up and thermal performance on the quote itself rather than waiting for submittals.
Hidden sash: MB-SR50N IW
On residential and design-driven projects, architects often want the operable vents to disappear into the facade. The MB-SR50N IW variant uses a concealed inward-opening vent, so fixed and operable bays read as one flat plane from the street. It is still a stick system, with the same advantages on site.
Matching the rest of the building
Mixed-use buildings need more than curtain wall. There are entrance doors at grade, punched windows on secondary elevations, terrace doors at setbacks. Because we fabricate windows, doors and curtain wall on the same floor, on matching profiles and finishes, the whole envelope can come from one shop and look like one building. Our commercial window systems service covers that full package, with shop drawings issued for the architect's approval before anything is cut.
What to send for an accurate quote
The faster we can see the real conditions, the more useful the first number is. For curtain wall, send:
- Elevations showing the grid, vents and spandrel zones
- Sections at the slab edge, head, sill and any setbacks
- A glazing schedule, even a preliminary one
- Any performance targets from the energy model or the spec
- Your planned sequence, if you already know how the building will be released
We come back with a line-by-line quote, recommendations where we see a better way to detail something, and the performance figures for the system as specified. Every quoted system comes with the documentation needed for submittal, which matters in New York, where the energy rules are among the strictest in the country.
Frequently asked questions
Is a stick curtain wall cheaper than unitized?
It depends on the building. Stick usually has lower up-front engineering and works better on smaller, irregular jobs, but it uses more field labor. On a tall tower with a highly repetitive grid, unitized can come out ahead. On most mid-rise and mixed-use work, stick tends to be the more practical choice.
Does Vitraz install the curtain wall?
No. We fabricate and supply. Your glazing sub or contractor erects the wall, and we do not bid installation or compete with your sub. If you need a crew, we can refer installers who know these systems.
Can a stick system handle a storefront at grade and curtain wall above?
Yes, and that is one of its strengths. The grid can change from floor to floor, and storefront, entrance doors and upper-floor curtain wall can all be built from matching profiles and finishes so the elevation reads as one design.
How do you handle out-of-plumb slab edges on a conversion?
Adjustable anchors and field-set mullions take up much of the variation in a stick system. We also recommend surveying the slab edges before final shop drawings so the details reflect the building as it actually stands, not as it was drawn.
What is the difference between MB-SR50N and MB-SR50N IW?
Both are stick-built Aluprof curtain wall systems. MB-SR50N is the standard mullion and transom grid with a 50 mm sightline. MB-SR50N IW adds a concealed inward-opening vent, so the operable parts are hidden and the facade reads as a flat plane.
Talk to us about your facade
If you are weighing stick against unitized on a mid-rise or mixed-use job, send us the elevations and sections and we will tell you honestly which approach fits the building and the site. Call me at (917) 418-0816 or get a free quote. No pressure. Just honest guidance from the people who will actually build your wall.